老版本把eth1,eth2绑定成一块网卡bond0新建配置文件如图:注意:bond0要把硬件地址一行删掉,否则重启network服务会失败完成。#cat/proc/net/bonding/bond0#查看bond0信息
#watch-n1"cat/proc/net/bonding/bond0"#监控此文件新版本(RHEL7)首先添加team0,设置模式,添加IP,..
分类:
其他好文 时间:
2015-08-25 12:25:11
阅读次数:
232
将网卡enp0s8、enp0s9进行链路绑定安装teamd包# yum install teamd创建一个team链接# nmcli con add con-name team0 type team ifname team0 config '{"runner":{“name”:"activeback...
分类:
其他好文 时间:
2015-08-17 23:33:33
阅读次数:
251
一、网卡绑定: 第一步:创建一个ifcfg-bondX #?vi?/etc/sysconfig/network-scripts/ifcfg-bond0
DEVICE=bond0
BONDING_OPTS="mode=0?miimon=100"
BOOTPROTO=none
ONBOOT=yes
BROADCAST=192.168.0.255
IPADDR=...
分类:
系统相关 时间:
2015-08-12 11:45:53
阅读次数:
224
将两张网卡绑定,共用一个IP,实现冗余效果。实际上linux双网卡的绑定模式有7种:
安装负载软件apt-get install ifenslave加载模块及配置负载vi /etc/modules添加bonding mode=0 miimon=100miimon是10ms监测一次网卡状态配置bond0注:bond IP与成员口的IP不能一致,如果不想成员口IP获得本网段地址,可以随便配置一个。...
分类:
系统相关 时间:
2015-06-26 13:29:06
阅读次数:
276
在给XenServer配置网卡bonding时,需要在所有节点都添加到集群之后再进行,这也是来自Citrix的建议:“Citrix
recommends never joining
a host that already has a bond configured
on it to a pool”。用XenCenter连接XenServer
集群,通过界面操作对网卡进行bonding...
分类:
其他好文 时间:
2015-05-06 09:19:10
阅读次数:
260
redhat5.5双网卡绑定后测试失败,现象为拔线不切换,cat/proc/net/bonding/bond0网卡始终up,ifconfig有与XEN有关的信息;经查与XEN有关系#chkconfigxendoff#chkconfigxendomainsoff#chkconfiglibvirtdoff#rebootOK一切都正常了
分类:
其他好文 时间:
2015-04-26 01:25:33
阅读次数:
150
首先,我们需要打开内核对 bonding 支持。设置内核 "make menuconfig/xconfig/config",在"Network device support"区段中选择"Bonding driver support",建议设置该驱动程序为模块,这样才能支持给驱动传递参数和设置多个bo...
分类:
系统相关 时间:
2015-04-24 12:15:38
阅读次数:
293
LinuxEthernetBondingDriverHOWTO Latestupdate:12November2007Initialrelease:ThomasDavis<tadavisatlbl.gov>Corrections,HAextensions:2000/10/03-15:-WillyTarreau<willyatmeta-x.org>-ConstantineGavrilov<const-gatxpert.com>-ChadN.Tindel<ctind..
分类:
Web程序 时间:
2015-04-21 01:58:51
阅读次数:
183
bond有7种模式,这是众所周知的。但是遇到这个奇怪的问题。我想把bond从模式0改为模式1。操作步骤是,修改/etc/modprobe.d/bonding.conf,把mode=0,改为了mode=1aliasbond0bondingoptionsbond0mode=1miimon=200然后重启网卡。通过,查看/proc/net/bonding/bond0,发现模式为rou..
分类:
系统相关 时间:
2015-04-07 20:17:25
阅读次数:
1245
Bonding的目的是为提高系统可用性,防止物理网口或线路的单点故障步骤1:检查Linux环境是否支持bonding,执行如下命令[root@compute~]#modinfobondingfilename:/lib/modules/2.6.32-431.el6.x86_64/kernel/drivers/net/bonding/bonding.koauthor:ThomasDavis,tadavis@lbl.govan..
分类:
系统相关 时间:
2015-03-31 13:05:09
阅读次数:
355