标签：raid；热备
构建软RAID5磁盘阵列&RAID设备恢复
)
为Linux服务器添加4块SCSI硬盘
使用mdadm软件包，构建RAID5磁盘阵列，提高磁盘存储的性能和可靠性
安装mdadm
准备用于RAID阵列的分区 -- 为Linux服务器添加4块SCSI硬盘，并使用fdisk工具个划分出一块2GB的分区依次为：/dev/sde1、/dev/sdg1、/dev/sdh1、/dev/sdf1 -- 将其类型ID更改为“fd”,对应为“Linux raid autodetect”,表示支持用于RAID磁盘阵列
创建RAID设备
创建热备磁盘
查看mdstat
设定faulty
再次查看mdstat
在RAID设备中建立文件系统
挂载并使用文件系统
设备恢复
查看mdadm.conf examples,根据这个创建mdadm.conf
一、准备用于RAID阵列的分区
[root@test2 jason]# fdisk /dev/sde
WARNING: DOS-compatible mode is deprecated. It‘s strongly recommended to
switch off the mode (command ‘c‘) and change display units to
sectors (command ‘u‘).
Command (m for help): p
Disk /dev/sde: 21.5 GB, 21474836480 bytes
255 heads, 63 sectors/track, 2610 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0xe4b1d138
Device Boot Start End Blocks Id System
/dev/sde1 1 262 2104483+ fd Linux raid autodetect
Command (m for help): n
Command action
e extended
p primary partition (1-4)
p
Partition number (1-4): 2
First cylinder (263-2610, default 263):
Using default value 263
Last cylinder, +cylinders or +size{K,M,G} (263-2610, default 2610): +2GCommand (m for help): t Partition number (1-4): fd Partition number (1-4): 2 Hex code (type L to list codes): fd Changed system type of partition 2 to fd (Linux raid autodetect)
Command (m for help): p Disk /dev/sde: 21.5 GB, 21474836480 bytes 255 heads, 63 sectors/track, 2610 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xe4b1d138 Device Boot Start End Blocks Id System /dev/sde1 1 262 2104483+ fd Linux raid autodetect /dev/sde2 263 524 2104515 fd Linux raid autodetect
Command (m for help): w The partition table has been altered! Calling ioctl() to re-read partition table. WARNING: Re-reading the partition table failed with error 16: Device or resource busy. The kernel still uses the old table. The new table will be used at the next reboot or after you run partprobe(8) or kpartx(8) Syncing disks.
[root@test2 jason]# fdisk /dev/sdg
WARNING: DOS-compatible mode is deprecated. It‘s strongly recommended to
switch off the mode (command ‘c‘) and change display units to
sectors (command ‘u‘).
Command (m for help): n
Command action
e extended
p primary partition (1-4)
p
Partition number (1-4): 2
First cylinder (263-2610, default 263):
Using default value 263
Last cylinder, +cylinders or +size{K,M,G} (263-2610, default 2610): +2GCommand (m for help): t Partition number (1-4): 2 Hex code (type L to list codes): fd Changed system type of partition 2 to fd (Linux raid autodetect)
Command (m for help): p Disk /dev/sdg: 21.5 GB, 21474836480 bytes 255 heads, 63 sectors/track, 2610 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x37970afa Device Boot Start End Blocks Id System /dev/sdg1 1 262 2104483+ fd Linux raid autodetect /dev/sdg2 263 524 2104515 fd Linux raid autodetect
Command (m for help): w The partition table has been altered! Calling ioctl() to re-read partition table. WARNING: Re-reading the partition table failed with error 16: Device or resource busy. The kernel still uses the old table. The new table will be used at the next reboot or after you run partprobe(8) or kpartx(8) Syncing disks. [root@test2 jason]#
[root@test2 jason]# fdisk /dev/sdh
WARNING: DOS-compatible mode is deprecated. It‘s strongly recommended to
switch off the mode (command ‘c‘) and change display units to
sectors (command ‘u‘).
Command (m for help): n
Command action
e extended
p primary partition (1-4)
p
Partition number (1-4): 2
First cylinder (263-2610, default 263):
Using default value 263
Last cylinder, +cylinders or +size{K,M,G} (263-2610, default 2610): +2GCommand (m for help): t Partition number (1-4): 2 Hex code (type L to list codes): fd Changed system type of partition 2 to fd (Linux raid autodetect)
Command (m for help): p Disk /dev/sdh: 21.5 GB, 21474836480 bytes 255 heads, 63 sectors/track, 2610 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xdeb9d0d0 Device Boot Start End Blocks Id System /dev/sdh1 1 262 2104483+ fd Linux raid autodetect /dev/sdh2 263 524 2104515 fd Linux raid autodetect
Command (m for help): w The partition table has been altered! Calling ioctl() to re-read partition table. WARNING: Re-reading the partition table failed with error 16: Device or resource busy. The kernel still uses the old table. The new table will be used at the next reboot or after you run partprobe(8) or kpartx(8) Syncing disks. [root@test2 jason]#
[root@test2 jason]# fdisk /dev/sdf
WARNING: DOS-compatible mode is deprecated. It‘s strongly recommended to
switch off the mode (command ‘c‘) and change display units to
sectors (command ‘u‘).
Command (m for help): n
Command action
e extended
p primary partition (1-4)
p
Partition number (1-4): 2
First cylinder (263-2610, default 263):
Using default value 263
Last cylinder, +cylinders or +size{K,M,G} (263-2610, default 2610): +2GCommand (m for help): t Partition number (1-4): f Partition number (1-4): 2 Hex code (type L to list codes): fd Changed system type of partition 2 to fd (Linux raid autodetect)
Command (m for help): p Disk /dev/sdf: 21.5 GB, 21474836480 bytes 255 heads, 63 sectors/track, 2610 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x65c9c4f1 Device Boot Start End Blocks Id System /dev/sdf1 1 262 2104483+ fd Linux raid autodetect /dev/sdf2 263 524 2104515 fd Linux raid autodetect
Command (m for help): w The partition table has been altered! Calling ioctl() to re-read partition table. WARNING: Re-reading the partition table failed with error 16: Device or resource busy. The kernel still uses the old table. The new table will be used at the next reboot or after you run partprobe(8) or kpartx(8) Syncing disks. [root@test2 jason]#
[root@test2 jason]# fdisk /dev/sdc
WARNING: DOS-compatible mode is deprecated. It‘s strongly recommended to
switch off the mode (command ‘c‘) and change display units to
sectors (command ‘u‘).
Command (m for help): n
Command action
e extended
p primary partition (1-4)
3
Invalid partition number for type `3‘
Command action
e extended
p primary partition (1-4)
p
Partition number (1-4): 3
First cylinder (5225-10443, default 5225):
Using default value 5225
Last cylinder, +cylinders or +size{K,M,G} (5225-10443, default 10443): +2GCommand (m for help): t Partition number (1-4): 3 Hex code (type L to list codes): fd Changed system type of partition 3 to fd (Linux raid autodetect)
Command (m for help): p‘ Disk /dev/sdc: 85.9 GB, 85899345920 bytes 255 heads, 63 sectors/track, 10443 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x8967e34e Device Boot Start End Blocks Id System /dev/sdc1 1261220980858+ 83 Linux /dev/sdc22613522420980890 8e Linux LVM /dev/sdc352255486 2104515 fd Linux raid autodetect
Command (m for help): w The partition table has been altered! Calling ioctl() to re-read partition table. WARNING: Re-reading the partition table failed with error 16: Device or resource busy. The kernel still uses the old table. The new table will be used at the next reboot or after you run partprobe(8) or kpartx(8)
[root@test2 jason]# partprobe /dev/sde sde sde1 [root@test2 jason]# partprobe /dev/sdg sdg sdg1 [root@test2 jason]# partprobe /dev/sdh sdh sdh1 [root@test2 jason]# partprobe /dev/sdf sdf sdf1 [root@test2 jason]# partprobe /dev/sdc sdc sdc1 sdc2 [root@test2 jason]# partx -a /dev/sde sde sde1 [root@test2 jason]# partx -a /dev/sdg sdg sdg1 [root@test2 jason]# partx -a /dev/sdh sdh sdh1 [root@test2 jason]# partx -a /dev/sdf sdf sdf1 [root@test2 jason]# partx -a /dev/sdf
[root@test2 jason]# partx -a /dev/sdf //按“enter”键 BLKPG: Device or resource busy error adding partition 1 [root@test2 jason]# [root@test2 jason]# [root@test2 jason]# partx -a /dev/sdf sdf sdf1 sdf2 [root@test2 jason]# partx -a /dev/sdf sdf sdf1 sdf2 [root@test2 jason]# partx -a /dev/sde //按“enter”键 BLKPG: Device or resource busy error adding partition 1 [root@test2 jason]# partx -a /dev/sde sde sde1 sde2 [root@test2 jason]# partx -a /dev/sdg //按“enter”键 BLKPG: Device or resource busy error adding partition 1 [root@test2 jason]# partx -a /dev/sdg sdg sdg1 sdg2 [root@test2 jason]# partx -a /dev/sdh sdh sdh1 [root@test2 jason]# partx -a /dev/sdh //按“enter”键 BLKPG: Device or resource busy error adding partition 1 [root@test2 jason]# partx -a /dev/sdh //按“enter”键 sdh sdh1 sdh2 [root@test2 jason]# partx -a /dev/sdc BLKPG: Device or resource busy error adding partition 1 BLKPG: Device or resource busy error adding partition 2 [root@test2 jason]# partx -a /dev/sdc sdc sdc1 sdc2 sdc3
[root@test2 jason]# fdisk -l | grep "/dev/sd[eghf]2" /dev/sde2 263 524 2104515 fd Linux raid autodetect /dev/sdg2 263 524 2104515 fd Linux raid autodetect /dev/sdf2 263 524 2104515 fd Linux raid autodetect /dev/sdh2 263 524 2104515 fd Linux raid autodetect [root@test2 jason]# fdisk -l | grep "/dev/sdc3" /dev/sdc352255486 2104515 fd Linux raid autodetect [root@test2 jason]#
二、创建RAID设备
[root@test2 jason]# mdadm -Cv /dev/md1 -a yes -n4 -l5 -x1 /dev/sd[eghf]2 /dev/sdc3 mdadm: layout defaults to left-symmetric mdadm: layout defaults to left-symmetric mdadm: chunk size defaults to 512K mdadm: size set to 2102272K mdadm: Defaulting to version 1.2 metadata mdadm: array /dev/md1 started. [root@test2 jason]#
-a：就是如果有需要创建的，就直接创建，比如说md0这个之前是不存在的目录，那么在创建阵列的同时直接创建md0
md1：一般把RAID命名成md0
-n：几块硬盘，就写几
-l：级别，或者说类型，5，就是RAID5
后面的路径信息时构成RAID的成员
-C：是创建阵列
-x是增加热备盘,即sdc3
[root@test2 jason]# ls -l /dev/md1 brw-rw---- 1 root disk 9, 1 Jun 20 13:07 /dev/md1
[root@test2 jason]# cat /proc/mdstat Personalities : [raid6] [raid5] [raid4] md1 : active raid5 sdh2[5] sdc3[4](S) sdg2[2] sdf2[1] sde2[0] 6306816 blocks super 1.2 level 5, 512k chunk, algorithm 2 [4/4] [UUUU] md0 : active raid5 sde1[5] sdf1[4] sdh1[2] sdg1[1] 6306816 blocks super 1.2 level 5, 512k chunk, algorithm 2 [4/4] [UUUU] unused devices: <none> [root@test2 jason]#
[4/4]：第一个4是代表4个分区，第二个4表示正常工作的有几个
[UUUU]：表示up，正常启动的有几个，如果有一个有问题，那么会用“_”（下划线）来表示。
上面sdf1[4]代表的是最后一个U
sde2[0]代表是第一个U
sdf2[1]则是第二个
sdg2[2]是第三个
sdh2[5]是第四个
三、在RAID设备中建立文件系统
[root@test2 jason]# mkfs -t ext4 /dev/md1 mke2fs 1.41.12 (17-May-2010) Filesystem label= OS type: Linux Block size=4096 (log=2) Fragment size=4096 (log=2) Stride=128 blocks, Stripe width=384 blocks 394352 inodes, 1576704 blocks 78835 blocks (5.00%) reserved for the super user First data block=0 Maximum filesystem blocks=1614807040 49 block groups 32768 blocks per group, 32768 fragments per group 8048 inodes per group Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912, 819200, 884736 Writing inode tables: done Creating journal (32768 blocks): done Writing superblocks and filesystem accounting information: done This filesystem will be automatically checked every 38 mounts or 180 days, whichever comes first. Use tune2fs -c or -i to override. [root@test2 jason]#
四、挂载并使用文件系统
[root@test2 jason]# mkdir /mdata2
[root@test2 jason]# cd / [root@test2 /]# ls -l | grep mdata2 drwxr-xr-x2 root root 4096 Jun 20 13:12 mdata2 [root@test2 /]# mount /dev/md1 /mdata2
[root@test2 /]# mount | grep "/dev/md1" /dev/md1 on /mdata2 type ext4 (rw)
[root@test2 /]# df -hT | grep "/dev/md1" /dev/md1 ext4 6.0G 141M 5.5G 3% /mdata2 [root@test2 /]#
五、修改/etc/fstab文件,实现开机自动启动
[root@test2 etc]# cp fstab fstab.bak2
[root@test2 etc]# vim fstab [root@test2 etc]#
[root@test2 etc]# umount /dev/md1
[root@test2 etc]# mount | grep "md1"
[root@test2 etc]# mount /mdata2
[root@test2 etc]# mount | grep "md1" /dev/md1 on /mdata2 type ext4 (rw)
六、设备恢复
[root@test2 etc]# mdadm -vDs ARRAY /dev/md0 level=raid5 num-devices=4 metadata=1.2 name=test2:0 UUID=10a00bcf:d67ab596:18b5fa25:8ef335e1 devices=/dev/sde1,/dev/sdg1,/dev/sdh1,/dev/sdf1 ARRAY /dev/md1 level=raid5 num-devices=4 metadata=1.2 spares=1 name=test2:1 UUID=8f4b5df4:f380ce6c:2ff605af:1b33ebcd devices=/dev/sde2,/dev/sdf2,/dev/sdg2,/dev/sdh2,/dev/sdc3 [root@test2 etc]#
[root@test2 /]# locate mdadm.conf /etc/mdadm.conf /usr/share/doc/mdadm-3.2.6/mdadm.conf-example /usr/share/man/man5/mdadm.conf.5.gz
先将exmple复制到/etc/mdadm.conf
[root@test2 /]# cd /usr/share/doc/mdadm-3.2.6/ [root@test2 mdadm-3.2.6]# vim mdadm.conf-example [root@test2 mdadm-3.2.6]# cd /etc [root@test2 etc]# ls -l | grep mdadm.conf -rw-r--r--1 root root181 Jun 16 17:05 mdadm.conf [root@test2 etc]# cp mdadm.conf mdadm.conf.bak [root@test2 etc]# cd /usr/share/doc/mdadm-3.2.6/ cp: overwrite `/etc/mdadm.conf‘? y [root@test2 mdadm-3.2.6]# cd /etc [root@test2 etc]# vim mdadm.conf [root@test2 etc]#
查看example:
[root@test2 etc]# vim mdadm.conf [jason@test2 ~]$ vim /usr/share/doc/mdadm-3.2.6/mdadm.conf-example
# mdadm configuration file # # mdadm will function properly without the use of a configuration file, # but this file is useful for keeping track of arrays and member disks. # In general, a mdadm.conf file is created, and updated, after arrays # are created. This is the opposite behavior of /etc/raidtab which is # created prior to array construction. # # # the config file takes two types of lines: # # DEVICE lines specify a list of devices of where to look for # potential member disks # # ARRAY lines specify information about how to identify arrays so # so that they can be activated # # You can have more than one device line and use wild cards. The first # example includes SCSI the first partition of SCSI disks /dev/sdb, # /dev/sdc, /dev/sdd, /dev/sdj, /dev/sdk, and /dev/sdl. The second # line looks for array slices on IDE disks. # #DEVICE /dev/sd[bcdjkl]1 #DEVICE /dev/hda1 /dev/hdb1 # # If you mount devfs on /dev, then a suitable way to list all devices is: #DEVICE /dev/discs/*/* # # # The AUTO line can control which arrays get assembled by auto-assembly, # meaing either "mdadm -As" when there are no ‘ARRAY‘ lines in this file, # or "mdadm --incremental" when the array found is not listed in this file. # By default, all arrays that are found are assembled. # If you want to ignore all DDF arrays (maybe they are managed by dmraid), # and only assemble 1.x arrays if which are marked for ‘this‘ homehost, # but assemble all others, then use #AUTO -ddf homehost -1.x +all # # ARRAY lines specify an array to assemble and a method of identification. # Arrays can currently be identified by using a UUID, superblock minor number, # or a listing of devices. # # super-minor is usually the minor number of the metadevice # UUID is the Universally Unique Identifier for the array # Each can be obtained using # # mdadm -D <md> # #ARRAY /dev/md0 UUID=3aaa0122:29827cfa:5331ad66:ca767371 #ARRAY /dev/md1 super-minor=1 #ARRAY /dev/md2 devices=/dev/hda1,/dev/hdb1 # # ARRAY lines can also specify a "spare-group" for each array. mdadm --monitor # will then move a spare between arrays in a spare-group if one array has a failed # drive but no spare #ARRAY /dev/md4 uuid=b23f3c6d:aec43a9f:fd65db85:369432df spare-group=group1 #ARRAY /dev/md5 uuid=19464854:03f71b1b:e0df2edd:246cc977 spare-group=group1 # # When used in --follow (aka --monitor) mode, mdadm needs a # mail address and/or a program. This can be given with "mailaddr" # and "program" lines to that monitoring can be started using #mdadm --follow --scan & echo $! > /run/mdadm/mon.pid # If the lines are not found, mdadm will exit quietly #MAILADDR root@mydomain.tld #PROGRAM /usr/sbin/handle-mdadm-events 65,1 Bot
[root@test2 jason]# mdadm -S /dev/md1 mdadm: unrecognised word on ARRAY line: levle=raid5 mdadm: Unknown keyword devices=/dev/sde2,/dev/sdg2,/dev/sdf2,/dev/sdh2 mdadm: Cannot get exclusive access to /dev/md1:Perhaps a running process, mounted filesystem or active volume group?
拼写错误
devices是未知的关键字
man mdadm.conf
devices= The value is a comma separated list of device names or device name pat-terns. Only devices with names which match one entry in the list will be used to assemble the array. Note that the devices listed there must also be listed on a DEVICE line.
[root@test2 jason]# vim /etc/mdadm.conf
[root@test2 jason]# vim /etc/mdadm.conf
[root@test2 jason]# cat /proc/mdstat Personalities : [raid6] [raid5] [raid4] md1 : active raid5 sde2[0] sdh2[5] sdg2[2] sdf2[1] 6306816 blocks super 1.2 level 5, 512k chunk, algorithm 2 [4/4] [UUUU] md0 : active raid5 sde1[5] sdf1[4] sdh1[2] sdg1[1] 6306816 blocks super 1.2 level 5, 512k chunk, algorithm 2 [4/4] [UUUU] unused devices: <none>
[root@test2 jason]# ls -lh /dev/md1 brw-rw---- 1 root disk 9, 1 Jun 20 20:34 /dev/md1
[root@test2 jason]# umount /dev/md1
[root@test2 jason]# mdadm -S /dev/md1 mdadm: stopped /dev/md1 [root@test2 jason]# cat /proc/mdstat Personalities : [raid6] [raid5] [raid4] md0 : active raid5 sde1[5] sdf1[4] sdh1[2] sdg1[1] 6306816 blocks super 1.2 level 5, 512k chunk, algorithm 2 [4/4] [UUUU] unused devices: <none>
[root@test2 jason]# mdadm -A /dev/md1 mdadm: /dev/md1 has been started with 4 drives. [root@test2 jason]# ls -l /dev/md1 brw-rw---- 1 root disk 9, 1 Jun 20 20:55 /dev/md1
[root@test2 jason]# mount /dev/md1 [root@test2 jason]# mount | grep "md1" /dev/md1 on /mdata2 type ext4 (rw) [root@test2 jason]#
[root@test2 jason]# cat /proc/mdstat Personalities : [raid6] [raid5] [raid4] md1 : active raid5 sde2[0] sdh2[5] sdg2[2] sdf2[1] 6306816 blocks super 1.2 level 5, 512k chunk, algorithm 2 [4/4] [UUUU] md0 : active raid5 sde1[5] sdf1[4] sdh1[2] sdg1[1] 6306816 blocks super 1.2 level 5, 512k chunk, algorithm 2 [4/4] [UUUU] unused devices: <none>
mdadm: set /dev/sde2 faulty in /dev/md1 [root@test2 jason]# cat /proc/mdstat Personalities : [raid6] [raid5] [raid4] md1 : active raid5 sdh2[5] sdf2[1] sde2[0](F) sdg2[2] 6306816 blocks super 1.2 level 5, 512k chunk, algorithm 2 [4/3] [_UUU] unused devices: <none>
[root@test2 jason]# mdadm /dev/md1 -r /dev/sde2 mdadm: hot removed /dev/sde2 from /dev/md1
[root@test2 jason]# cat /proc/mdstat Personalities : [raid6] [raid5] [raid4] md1 : active raid5 sdh2[5] sdf2[1] sdg2[2] 6306816 blocks super 1.2 level 5, 512k chunk, algorithm 2 [4/3] [_UUU] unused devices: <none>
本文出自 “Code Life” 博客，请务必保留此出处http://zencode.blog.51cto.com/11714065/1791671
标签：raid；热备
原文地址：http://zencode.blog.51cto.com/11714065/1791671
