标签：usart 主频 acm 数组 ase 允许 定时 eee height
//超时时间定义
#define UART1_TimeoutComp 2 //20ms
#define UART2_TimeoutComp 10 //100ms
#define UART3_TimeoutComp 10 //100ms
u8 UART1_Timeout,UART2_Timeout,UART3_Timeout;
u16 UART1_FlagTemp,UART2_FlagTemp,UART3_FlagTemp;
u8 uart1_data_temp[200],uart2_data_temp[500],uart3_data_temp[500];
//定时器初始化
void TimerInit(void)
{
//定时器初始化数据结构定义
TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure;
//初始化定时器，用于超时接收，20ms
TIM_TimeBaseStructure.TIM_Period = 100; //计数上限，100*100us = 10000us = 10ms
TIM_TimeBaseStructure.TIM_Prescaler = 4799; //预分频4800,48MHz主频，分频后时钟周期100us
TIM_TimeBaseStructure.TIM_ClockDivision = TIM_CKD_DIV1; //不分频
TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up; //向上计数
TIM_TimeBaseStructure.TIM_RepetitionCounter=0;
//初始化
TIM_TimeBaseInit(TIM2,&TIM_TimeBaseStructure);
DMA_DeInit(DMA1_Channel5); //将DMA的通道1寄存器重设为缺省值
DMA_InitStructure.DMA_PeripheralBaseAddr = (u32)SRC_USART1_DR; //源头BUF既是 (&(USART1->DR))
DMA_InitStructure.DMA_MemoryBaseAddr = (u32)uart1_data_temp; //目标BUF 既是要写在哪个个数组之中
DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralSRC; //外设作源头//外设是作为数据传输的目的地还是来源
DMA_InitStructure.DMA_BufferSize = 200; //DMA缓存的大小 单位在下边设定
DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable; //外设地址寄存器不递增
DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable; //内存地址递增
DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte; //外设字节为单位
DMA_InitStructure.DMA_MemoryDataSize = DMA_PeripheralDataSize_Byte; //内存字节为单位
DMA_InitStructure.DMA_Mode = DMA_Mode_Circular; //工作在循环缓存模式
DMA_InitStructure.DMA_Priority = DMA_Priority_High; //4优先级之一的(高优先)VeryHigh/High/Medium/Low
DMA_InitStructure.DMA_M2M = DMA_M2M_Disable; //非内存到内存
DMA_Init(DMA1_Channel5, &DMA_InitStructure); //根据DMA_InitStruct中指定的参数初始化DMA的通道1寄存器
DMA_ITConfig(DMA1_Channel5, DMA_IT_TC, ENABLE); //DMA5传输完成中断
USART_DMACmd(USART1,USART_DMAReq_Rx,ENABLE); //使能USART1的接收DMA请求
//串口初始化，只列出一个通道，其他两个通道相同
void USART1_Configuration(void)
{
//串口初始化数据结构定义
USART_InitTypeDef USART_InitStructure;
//定时器中断服务程序
void TIM2_IRQHandler(void)
{
u16 i;
//清定时器中断
TIM_ClearITPendingBit(TIM2, TIM_FLAG_Update);
if(i!=uart1_Flag_last) //未完成传输
{
UART1_Timeout=0;
uart1_Flag_last=i;
}
else
{
if(UART1_Timeout>UART1_TimeoutComp) //产生超时
{
if(i<200) //有数据接收到
{
UART1_FlagTemp=200-i; //得到接收到的字节数
for(i=0;i<UART1_FlagTemp;i++) //将数据拷贝到缓冲区
uart1_data[i]=uart1_data_temp[i];
UART1_Flag=UART1_FlagTemp;
DMA_ClearFlag(DMA1_FLAG_TC5);
DMA_Cmd(DMA1_Channel5, DISABLE); //正式允许DMA
DMA5_Init();
}
UART1_Timeout=0;
}
}
//------------------------------------------------------------------
i=DMA_GetCurrDataCounter(DMA1_Channel6);
DMA_ClearITPendingBit(DMA1_IT_GL6); //清除全部中断标志
for(i=0;i<UART2_FlagTemp;i++) //将数据拷贝到缓冲区
uart2_data[i]=uart2_data_temp[i];
UART2_Flag=UART2_FlagTemp;
DMA_ClearFlag(DMA1_FLAG_TC6);
DMA_Cmd(DMA1_Channel6, DISABLE); //正式允许DMA
DMA6_Init();
}
UART2_Timeout=0;
}
}
//------------------------------------------------------------------
i=DMA_GetCurrDataCounter(DMA1_Channel3);
DMA_ClearITPendingBit(DMA1_IT_GL3); //清除全部中断标志
for(i=0;i<UART3_FlagTemp;i++) //将数据拷贝到缓冲区
uart3_data[i]=uart3_data_temp[i];
UART3_Flag=UART3_FlagTemp;
DMA_ClearFlag(DMA1_FLAG_TC3);
DMA_Cmd(DMA1_Channel3, DISABLE); //正式允许DMA
DMA3_Init();
}
UART3_Timeout=0;
}
}
}
STM32串口DMA超时接收方法，可大大节约CPU时间
标签：usart 主频 acm 数组 ase 允许 定时 eee height
原文地址：http://www.cnblogs.com/zym0805/p/7339913.html
